How to check the correct air conditioner block

How do you know? how to check the air conditioner block the most exactly. We invite you to follow our article below to help you understand more.

1. How to recognize a broken air conditioner block

When you are using the air conditioner and see the following signs frequently appearing below, it is very likely that the air conditioner block is not running:

The air conditioner block is abnormally hot when it is turned on and you feel that the outdoor unit fan does not emit heat out.

How to identify damaged air conditioner block very easily

Unstable air conditioner provides erratic cold air, the machine works but the room temperature is hot and cold at times.

Copper pipes, pipe connectors have a layer of white snow on the outside when you are using them air machine The temperature causes the air conditioner to show signs of leaking water and sticking to snow.

The fan of the outdoor unit and indoor unit work normally, but you will feel the cold air coming out not cold, but only the wind when turning on the air conditioner in the room, sometimes even emitting hot air from the indoor unit, feeling very uncomfortable.

There is a strange sound when you hear in the outdoor unit of the air conditioner, the air conditioner runs with noise and is very loud.

See more:  What to do if BIOS cannot detect ATA/SATA hard drive in Windows?

The outdoor unit is switched on and off continuously, I don’t understand why there is such a problem.

2. How to check the air conditioner block is very easy

How to check the air conditioner block you need to do the following issues that you need to master, avoid the situation that you don’t know anything and call the repair service and get cheated:

2.1. Check the electrical part of the block

Check coil:

Check block coil: Use a multimeter using an X1 or 10 Ohm scale to measure the resistance of each pair of block contacts. If the resistance readings of certain pairs are absent, they may have broken coils. If all pairs of contacts show resistance, the machine will still work normally.

Check block shell touch: Use a multimeter to measure the resistance at the machine’s contact pile with the outer shell. If any electrical terminal appears to have a resistance, the block will leak electricity. If the needle is not it should indicate that the coil is not leaking well.

Check winding insulation: Next check the compressor current. Plug in the power for the compressor to work and then use clamps to one of the 3 wires of the air conditioner compressor. If the current value of the wire is higher than the rated value, the block is damaged due to current eating. If the current is equal to the rated current written on the block, that’s fine. If the compressor is not working, it is damaged due to piston jam or broken coil.

2.2. Check the muscle part of the block

– Check the steam part in how to check the air conditioner block:

See more:  How to create a Bat file to quickly open multiple websites on Windows 10

+ Step 1: Supply power to the compressor to operate.

How to check the air conditioner block check the steam part

+ Step 2: Use your hand to cover the end of the push tube for about 15s to 20s.

+ Step 3: If the compressor works well, the hand will not be able to block the thrust, it can be concluded that the slightly blocked part is still good.

– Check the tightness of the thrust valve – How to check the air conditioner block:

+ Step 1: Supply power to the compressor to operate.

+ Step 2: Use your hand to cover the end of the push tube for about 15 seconds to 20 seconds until you can’t hold it anymore, then turn off the machine but keep your hand in that position.

The way to check the air conditioner block is to check the ejector valve part

+ Step 3: Wait for about 1 minute and then release your hand slowly, if the air is strong, the valve will still be closed. If the air is weak or there is no air, the valve is open.

+ Step 4: It can be concluded that the slightly blocked part is still good in how to check the air conditioner block.

– Check starting power under load:

+ Step 1: Power the block to work and then tightly seal the hand at the top of the push tube until it can’t be blocked anymore, then pull out the power, but keep the hand still as above.

+ Step 2: After about 10 years, power on again, if the compressor can start right away, that’s good.

+ Step 3: If the block does not restart immediately, it is a weak block.

– Check the noise level of the cyclone:

See more:  How to turn off User Account Control (UAC) on Windows 10

+ Step 1: Let the block run and listen when the block works without load to see if it is quiet, has any strange noises.

+ Step 2: Next, use your hand to seal the push pipe until it can’t be sealed anymore, then the other hand touches the suction head if the block works smoothly, it’s good, if the block is big, it’s bad.

3. The reason why the air conditioner block is not running

– The installation of the wrong air conditioner is not in accordance with the standards.

– Installed in the wrong position, the outdoor unit is exposed to direct sunlight without shielding, leading to the outdoor unit not being able to exchange heat, causing overload.

>> See more:

Concept air conditioner blockinformation you need to know.

Sharp air conditioner flashes yellow light: Causes & solutions.

How to check the air conditioner block with causes

– The power supply to the air conditioner is not stable, which can easily cause fire and block damage.

– The air conditioner has a small capacity but is installed in a large room, exceeding the manufacturer’s regulations, causing the machine to run continuously without rest, leading to overload.

=> How to fix: When you encounter a damaged air conditioner block, you should not be too worried, just call a reputable repair center like TechtipsNReview.com will come and check it out at home for you.

Above is how to check the air conditioner block damaged very precisely. Thank you for watching.

TechtipsNReview.com

Source: How to check the correct air conditioner block

– TechtipsnReview

, , , ,

Leave a Reply

Your email address will not be published. Required fields are marked *