Instructions to install Win 7/8/10 in WinPE environment (Mini Win)

NOTE: Welcome to the Knowledge Sharing Blog! If you encounter any errors during use, such as error in download link, slow blog loading, or unable to access a certain page on the blog … please notify me. via Contact page. Thanks!

There have been many articles that techtipsnreview introduced and instructed you how to reinstall Windows for your computer, but it seems that is not enough ?

Honestly, for you to write blog guides like me, you will know how many requests arise, each person has a preference and each person has a different question on the same topic.

To respond to everyone’s requests, in this article I will guide you how to install Windows 7/8 / 8.1 / 10 from the Mini Windows environment with the WinNTsetup tool.

#first. What needs to be prepared?

1. First, create a multi-function bootable usb.
2. File * .iso Windows (Win whatever you want). You can go online to download the original Windows Setup, if you intend to install Windows 10, you can download the installer as in this guide.

Just that simple, the necessary tools are already available in the usb boot that you created earlier.

Related posts:

#2. How to install Win on the WinPE environment

Or do the following:

Now, plug the USB into the computer and boot into the Mini Windows 7 or 8 environment. If you do not know how to boot into your computer, you can refer to this tutorial.

+ Step 1: Into the Computer => and Format hard drive partition where you want to install Windows (in the section File Type => you remember to choose is NTFS Please).

You should uncheck the checkbox Quick Format Before proceeding to Format hard drive, we will format the hard drive in normal mode will be better.

Tips: In addition to the above, you can use Partition Winzard software to delete the partition you want to install Win on.

Wait a while for Format computer, it also takes a while because we have dropped the Quick Format mode. Once done, move on to the next step.

+ Step 2: Click on the icon DLC BOOT => select Disk Tools => select tool BootICE.

Next we will set up to load MBR, PBR for the hard drive partition that we just Format:

Choose Physical => select the correct partition you just Format earlier => click Process MBR => select Windows NT 5.x/ 6.xMBR => select Install/ Config. You do it in turn as shown below:

Choose the latest version and use it.

+ Continue to click Process MBR => select the correct hard drive partition that you just Format => select Install/ Config and press OK to install. You set up as shown below.

+ Step 3: This step we will have 2 ways to install that is “Mount” to the virtual drive to install directly with the file setup.exe is in the installer, and the second way we will use the WinNTsetup tool included in USB BOOT.

+ Option 1: Mount the Windows setup file to the virtual drive by right-clicking the file *.iso that => and select Mount as ImDisk Virtual Disk. This time it will automatically create for us a virtual drive containing the Windows installer in it.

Then proceed to install as usual, you can refer to the article on how to install Windows if you do not know.

# 3. How to use WinNTsetup to install Windows

+ Method 2: Use the WinNTsetup tool to install. To do this, you first click Mount iso file to virtual drive as instructed in method 1.

Then click on the icon DLC BOOT => select System => open the software WinNTSetup Up as shown below:

At the main interface of WinNTsetup you set up as follows. Choose Windows Vista/7/8/2008/2012 if you are installing Windows 7 or higher.

Next at the frame Select location of the install.wim file => you click Search to find the file install.win or install.esd in the virtual drive you burned earlier.

Important Note: There must be 3 green ticks like in the red frame, I have circled them to work, but if there is a yellow exclamation mark or red x, the installation will not be performed.

If I do the steps as instructed above, I make sure there is no error here.

You do as shown below to open the file install.win (file install.win or install.esd located in the Folder sources Please )

You set up as follows:

At the frame Select localtion of the installation driver => you click Search.. => and select the correct partition that you want to install win.

1. Check the box Patch UxTheme.dll to allow unsigned Themes
2. Tweaks: Set advanced options if you want (in this there are quite a lot of great features you can go to see, if you do not understand, you can use google translate offline: D)
3. Setup: Start the windows installation process.
4. In addition, at the Option Edition section you can choose the Windows operating system you are installing.

Note: When you press is Setup There will be a message asking if you want to choose the boot mode with BootICE or another mode in the section Boot Menu.

In the old version I am using, there is only one option BootICE But in newer versions of WinNTsetup there is an option BootSect (ie the default Windows Setup). We encourage you to choose the BootICE mode.

OK, now let’s make a cup of coffee while waiting for the software to start installing Win. Once done it will show up a notice as shown below. Click OK and restart your computer to finish installing Win.

# 3. Epilogue

That is done with the tutorial install windows in a WinPE environment Okay, the instructions are lengthy, but the operation is extremely fast.

Hopefully this new win installation method will help you in the rescue of the computer, in addition to this way to install windows for the computer, you can refer to other ways here.

Good luck !

Kien Nguyen – techtipsnreview